Tech Breakdown: A Detailed Account of ColorFabb SteelFill Filament

With ground-up metallic powder as their distinctive ingredient, metal-filled PLAs should not solely heavier than their PLA-only counterparts, but in addition usually have traits which lend themselves generously to post-processing prospects – which may actually make them pop. Made shiny or left uninteresting, they are often distinguished simply when in comparison with the same old filament selections available on the market as we speak.

Let’s take a better take a look at the latest in ColorFabb’s line of those fun-to-print filaments: SteelFill.

Iron Man is aware of metal is superior.

Suggestions & Settings for SteelFill

Like its predecessors, SteelFill is a PLA-based filament so most settings that work for PLA filament may even work for SteelFill. Utilizing MatterControl, you may simply begin with a typical PLA preset on your printer and tweak particular person settings from there.

Within the experiences I’ve had with SteelFill and the opposite metal-filled PLAs from ColorFabb, I’ve discovered that they have an inclination to wish a little bit extra warmth than common PLA to realize a great soften and movement.

Extruder Temperature: 200-220°C

Relying on the printer the extrusion temperature could range. The vary above ought to cowl most printers. Begin with 205 and regulate if essential.

Mattress Adhesion: Heated glass with glue or no heated mattress with painter’s tape

In case your printer has a heated mattress you may print straight on the glass. Set it to 60°C and if wanted, apply glue stick.

In case your printer doesn’t have a heated mattress lay down some blue painter’s tape with or with out glue. Simply ensure that to account for the additional thickness of the tape in your Z Offset (normally up 0.1 mm) in order that first layer is ideal.

Printed straight on glass, heated mattress at 60°

Print Velocity: 50-70 mm/s

Like PLA, SteelFill can print at greater speeds. Simply regulate the extrusion for the primary few full-speed layers to verify your scorching finish can assist the highest velocity you’ve chosen.

Nozzle

SteelFill is abrasive, so a metal nozzle is a should. Hardened metal or stainless-steel nozzles can be found within the MatterHackers retailer.

Retraction

As with all PLAs, an excessive amount of retraction may cause warmth creep. Make certain to regulate the print in the course of the first few layers which use retraction extra closely for strikes between islands (if relevant) and decrease if essential as a caught or sluggish filament movement will definitely be a supply of frustration if left unmonitored.

Layer cooling

Followers are beneficial, particularly for overhangs. Remember the fact that for the reason that materials is extra dense it’s heavier and can droop extra simply than common PLA.

Publish-processing

SteelFill 3D filament provides many prospects for enhancing the outside after printing. We’ve had success of various sorts utilizing sandpaper, a wire brush, a rock tumbler, and mixtures of the three. Use XTC if you would like a shiny end.

For extra in-depth PLA ending methods, take a look at our article “How To: Easy and End Your PLA Prints – Half 1.”

The decrease proper facet was coated with tape whereas the opposite was sanded – the gloss is from printing on glass

SteelFill vs. Different 3D Supplies

SteelFill is similar to the opposite ColorFabb metal-filled PLAs when it comes to weight and really feel post-print, and has the identical fundamental traits apart from the plain look.

As a PLA-based filament, SteelFill embodies many of the similar traits as PLA, so it’s going to warp when uncovered to warmth (like sunshine) and no matter having precise steel in it, shouldn’t be used for any sort of mechanical software.

To measure SteelFill in opposition to different 3D filament, take a look at our Filament Comparability Information. 

Conclusion

With a silver metallic aesthetic and a few hefty weight to it, SteelFill has proved to be one more nice specialty filament choice from ColorFabb. Artists, hobbyists, and professionals alike will discover a use for it as they proceed to discover the unending prospects of 3D printing.

Right here’s just a few footage of a Lincoln Bust that I printed and completed. Have enjoyable with SteelFill!

The uncooked print on a SeeMeCNC Orion – loads of flaws and a few very barely shifted layers

The chin didn’t maintain up and a few extrusions fell. These should be minimize off

Simply displaying the contours of the pinnacle – these will quickly be smoothed

This layer shift on the again of the print will quickly be sanded away

No extra layer shift line!

After a half hour of sanding and wire brush, the mannequin may be very shiny! The print behind is from a earlier try however the assist materials wouldn’t come off.