This weekend’s 3D Printing Information Briefs are all about analysis! We’ll begin with what’s been known as the primary comparability of corrosion resistance in 3D printed magnesium and zinc alloys. Then, scientists on the current European Society for Organ Transplantation Congress reported a serious step ahead in diabetes analysis, and researchers in Korea developed and validated a 3D printed pores and skin imitation layer for radiation dosing. Lastly, Lithuanian researchers are 3D printing small stents utilizing two-photon polymerization.
Research Compares Corrosion Resistance in 3D Printed Mg and Zn Bioalloys
SEM pictures and EDS maps of the WE43MEO corroded surfaces after the PDP checks. Left facet of the panel corresponds to the extruded pattern and proper facet to the LPBF pattern.
Researchers from the IMDEA Supplies Institute, the Helmholtz-Zentrum Hereon Institute of Floor Science, and Meotec GmbH performed what they name the primary comparability of corrosion resistance in bioabsorbable WE43 magnesium and Zn1Mg zinc alloys produced with materials extrusion and laser powder mattress fusion (LPBF) 3D printing. Their research can be mentioned to be the primary to make use of electrochemical testing in a buffered saline resolution to match how the degradation of those biodegradable metals is affected by their manufacturing strategies. The experimental portion occurred underneath the Horizon Europe BIOMET4D challenge. The crew discovered that the LPBF printed samples corroded a lot quicker than the extruded ones: within the WE43 samples, yttrium oxide particles weakened the corrosion layer’s protecting impact, and with the Zn1Mg, an elevated quantity of eutectic phases sped up microgalvanic degradation. A plasma electrolytic oxidation (PEO) floor therapy was utilized to all samples to type a protecting oxide layer and enhance their corrosion resistance. The outcomes may lay the groundwork for safer, long-lasting biodegradable implants.
“Nonetheless, the WE43MEO LPBF specimens confirmed excessive corrosion charges regardless of PEO therapy, which was linked to heterogeneities in oxide layer thickness,” defined first creator Guillermo Domínguez. “In distinction, PEO therapy had the other impact on Zn1Mg samples, the place LPBF specimens demonstrated better corrosion resistance than the extruded ones.”
ESOT Researchers 3D Print Insulin-Producing Pancreas Cells
A human pancreatic islet visualised utilizing double immunostaining with glucagon antibody (pink) and insulin antibody (blue). Credit score: Afferent (CC BY-SA 3.0)
On the European Society for Organ Transplantation (ESOT) Congress 2025, a crew of scientists introduced an thrilling breakthrough that might end in simpler, and fewer invasive, kind 1 diabetes (T1D) therapy. They had been capable of efficiently 3D print human islets (insulin-producing cell clusters within the pancreas) utilizing a novel bioink made out of decellularized human pancreatic tissue and alginate. Historically, islet transplants are infused into the liver, which regularly ends in main lack of cells and solely restricted success. These researchers designed the 3D printed islets to be implanted just below the pores and skin, which is a a lot much less invasive process. A sluggish print velocity of 20 mm/minute and low stress (30 kPa) stored the islets secure throughout printing and helped them hold their pure form. This resulted in high-density, sturdy islet buildings that remained alive and purposeful in laboratory checks for as much as three weeks. A porous structure enhanced the move of oxygen and vitamins to the embedded islets, which promoted vascularization and helped preserve cell well being. Lastly, the 3D printed islets maintained their buildings; responded higher to glucose, releasing insulin when wanted; and, by the twenty first day, they had been higher capable of sense and react to blood sugar ranges.
“Our objective was to recreate the pure atmosphere of the pancreas in order that transplanted cells would survive and performance higher. We used a particular bioink that mimics the help construction of the pancreas, giving islets the oxygen and vitamins they should thrive,” defined lead creator Dr. Quentin Perrier of Wake Forest College’s Institute for Regenerative Medication (WFIRM).
“This is without doubt one of the first research to make use of actual human islets as an alternative of animal cells in bioprinting, and the outcomes are extremely promising. It means we’re getting nearer to creating an off-the-shelf therapy for diabetes that might at some point eradicate the necessity for insulin injections.”
The crew is now testing the bioprinted islets in animal fashions and exploring long-term storage choices, to be able to make the remedy extra broadly obtainable.
3D Printed Pores and skin Imitation Layer for Dose Evaluation
Researchers from Hanyang College and the College of Ulsan School of Medication developed a 3D printed pores and skin imitation layer (SIL) to make use of for real-time localized pores and skin evaluation. As they clarify of their analysis paper, pores and skin is usually uncovered to radiation, and a physician’s therapy plan for his or her sufferers who want radiation should set up the absorbed dose earlier than deterministic signs set in. So it’s vital to have a quick however correct dose evaluation device, however most conventional strategies take too lengthy don’t present direct dose measurements, or don’t replicate human pores and skin carefully sufficient. The crew made a 3D printed SIL, with a 50 μm thick Dermis Layer and Basal Layer, that may assist physicians “consider the feasibility of localized pores and skin dose evaluation.” Their SIL, which does carefully resemble pores and skin, is able to real-time measurement of pores and skin absorbed doses of radiation utilizing plastic scintillators, which had been additionally 3D printed.
“Thickness measurements confirmed values near the design, and tissue equivalence was assessed by way of compositional evaluation and Monte Carlo simulation utilizing the MCNPX code. The absorbed dose per fluence (𝐷/𝛷) for alpha particles, electrons, and photons confirmed good settlement with dose conversion coefficients from the ICRP 116 report throughout most power ranges. As well as, experimental verification was performed utilizing 4 gamma sources. The radiation responsiveness of the SIL was confirmed by isolating the scintillation sign from the BL utilizing a subtraction based mostly method. These outcomes counsel that the SIL displays tissue-equivalent bodily and radiological properties and has potential to be used as a retrospective dosimeter or in scientific functions for localized pores and skin dose evaluation,” the researchers concluded.
Two-Photon Polymerization 3D Printing of Small Stents
The schematics current the research workflow. First, CAD fashions of stents had been generated. The printing course of adopted, with the objective of getting ready buildings for mechanical and organic testing. Moreover, cylinder samples had been ready from the identical materials because the stents. Mechanical testing was carried out in two steps – experimental materials characterization and in silico modeling. Lastly, stents had been validated utilizing rats in vivo.
The World Well being Group (WHO) says that one of many main causes of demise globally are cardiovascular illnesses (CVDs), together with coronary artery illness (CAD), the place the blood vessels slender and turn out to be laborious. A collaborative crew from Lithuanian College of Well being Sciences, Vilnius Gediminas Technical College, and Vital3D Applied sciences are utilizing two-photon polymerization, or 2PP, 3D printing to fabricate stents to deal with the narrowing of blood vessels. 3D printing is ready to make advanced architectural buildings out of quite a lot of supplies, making it engaging for producing medical gadgets like stents. However the expertise isn’t with out its limitations, equivalent to some strategies being unable to succeed in sub-μm ranges of floor roughness, which medically viable stents want. So the crew turned to 2PP, which is predicated on “nonlinear interplay between femtosecond laser mild and photo-active resin” and has “limitless 3D geometry potential.” They efficiently used 2PP to 3D print stents for blood vessels as small as simply 5 mm tall and 0.7 or 0.9 mm in diameter, and 3D struts as skinny as 50 μm.
“A number of novel approaches had been launched to accommodate the printing of such a construction like voxel elongation and printing in stereolithography-like vat-sample holder configuration. Moreover, the produced stents had been examined mechanically proving their mechanical resilience to most typical varieties of mechanical deformations. Experimental outcomes had been additionally in comparison with mathematical modeling, displaying glorious settlement, hinting at the potential for designing and testing advanced micro-stent geometries earlier than fabrication in silico. Lastly, biocompatibility experiments had been carried out, wherein rats survived the 7-day incubation interval and confirmed no important biocompatibility points,” the researchers wrote of their research.
Subscribe to Our E-mail Publication
Keep up-to-date on all the most recent information from the 3D printing business and obtain data and provides from third get together distributors.
Add your 3D Fashions and get them printed shortly and effectively.
